V - 30SL
V30 - 30SL "V30SL" is a handmade tube Distortion for an electric guitar, based on principles of restriction of a signal. "V30SL" is equipped with three tubes "12AX7", essentially different three types of limitation of a signal ((Distortion))and the adjustable passive filter, which is adjusted to limitation of a signal.
These constructive peculiarities allow in details to control and if necessary to accent a timbre of sounding of your electric guitar - from a bright sound of the 1980s up to "dense" modern sounding. Huge in its tonal range and an opportunity of a choice of type of limitation of a signal (Distortion) in a combination with low parameters of noise levels and a background will give necessary open space for creativity.
Assembling of "V30SL" tube Distortion is executed with use of hinged installation, with application of silver wires with phtoroplastic isolation. The frame of "V30SL" is made of 1.5 mm steel.
In the scheme of this device it is not using active filters, that positively affects on a sound. Channels "CRUNCH", "LEAD" and "HI-GAIN" are balanced with each other according to loudness. The scheme is sensitive to the slightest nuances using musical instrument and thus does not change individual character of a sound of your guitar.
Front panel:
GAIN - depth of amplification
MODE - adjustable passive low frequency filter (6 fixed positions), regulates low frequencies before the limitation of the signal
TONE - the passive filter of high frequencies
LEVEL - a level of loudness of effect
BYPASS - (cold bypass of the effect), mechanical switching, no electronic switches are used
There are used three different types of limitation of a signal (Distortion) in the scheme of "V30SE":
CRUNCH - classical type of tube Distortion
LEAD - the Distortion used earlier in a series "T324" - "T325", but in "V30SL" it has other operating mode.
Diode indication "CRUNCH" / "LEAD": red color corresponds to "LEAD", green - "CRUNCH"
On the rear panel, where the jacks for connecting guitar cables are situated, there is also a switch for switching between the limiting modes (hard or soft limiting). This function affects the degree of production of high harmonics, enabling to precisely control the harmonics and to make your guitar sound as expressively as possible. The circuit has some small amendments such as additional passive filtering before the limiting phase and after it.
HI - GAIN in essence the new type of tube Distortion, was not used earlier in any serial device construction of a similar class. Constructive peculiarities of the given scheme allows to achieve deeper effect "Distortion" without "blocking effect" of a tube on low frequencies.
Recommendations to application:
Channel "CRUNCH" - potentiometer "Gain" on a maximum, " Mode " - 4, 5, 6th positions. It is possible to receive very dense on a timbre "Distortion" with good dynamics while using humbucker at such adjustments.
Channel "CRUNCH" - potentiometer "Gain" at 9-12 o'clock, " Mode " - at 6th position: Such adjustments are recommended using "single".
Channel "CRUNCH" - "Gain" at 8 o'clock, " Mode " - 1, 2, 3 positions. Such adjustments are recommended whilst using humbucker.
Channel "CRUNCH" - "Gain" at 8 o'clock, " Mode " - 2,3 positions. Such adjustments are recommended whilst using "single" if it is necessary to receive very bright sound ("glass") by chords.
Channel "LEAD" - "Gain" at 1-2 o'clock, " Mode " - 4th position. Modern and dense "Distortion" with longer sustain and stronger compression of a signal, than have "CRUNCH".
Channel "LEAD" - "Gain" at 3-4 o'clock, " Mode " - 1st position: Classical "Distortion" for playing in style "Hard-N-Heavy" from the 80s, but with longer sustain.
"HI-GAIN" adds to channel "LEAD" new "high" harmonics. In this case it is recommended to put potentiometer “GAIN” no more than at 12-13 o’clock, ”MODE” 3,4 positions.
"HI-GAIN" - "Gain" at 2-3 o'clock, " Mode " 2 - 4th position: Such adjustments are recommended whilst using pickups, which have weaker signal on an output in comparison with usual humbucker. (" Dimarzio YJM model ", "dp 404" in a position "NECK").
TECHNICAL SPECIFICATIONS:
Input Impendence : 1M
Output Impendence : 50kohm
Dimensions of the case: 238 x 154 mm
Weight: 2300 gr
Weight of a separate power unit: 700 gr
ORDER |
